Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies HVAC Cleaning in Fort Worth: What to Know First
We provide independent Abatement Technologies HVAC cleaning in Fort Worth for homeowners who need evaporator coil, blower, condenser, air handler, and heat exchanger service. Most Abatement Technologies jobs in Fort Worth run two to four hours from arrival to final test, with a written price delivered before we touch a single panel. Our equipment roster includes Abatement Technologies-compatible negative-pressure extractors and coil treatment systems, and every job ends with a Documented Photo Record of the cleaned components.
This page is for Fort Worth homeowners who own Abatement Technologies air filtration, abatement, or remediation equipment and want a technician who knows the difference between a PREDATOR 750 and a BD2KL without reading the nameplate twice. If your Abatement Technologies unit is showing reduced airflow, unusual coil icing, or blower motor strain, call (817) 520-8797. We’ll put a written estimate next to any competitor’s quote, free.
How Abatement Technologies Products Fail - and How We Fix Them
- PREDATOR 750 Series: Blower motor bearing fatigue from Fort Worth’s hard-water scale and limestone dust. The PREDATOR 750’s direct-drive blower runs at fixed high RPM, and Fort Worth’s mineral-heavy water supply produces scale that bakes onto the blower wheel in air handler applications. We remove the wheel assembly, media-blast scale from the vanes under controlled negative pressure, and treat the bearings with OEM-compatible lubricant. If the bearing play exceeds 0.5mm, we document it and quote a replacement before installation.
- BD2KL Portable Air Scrubber: Clogged HEPA pre-filter causing negative-pressure drop across the coil. The BD2KL’s compact footprint means the pre-filter loads fast in Fort Worth’s pollen-heavy spring (oak and ragweed peak April through June). Homeowners notice reduced exhaust velocity first. We pull the filter bank, photograph the loading pattern, and replace with Abatement Technologies-specified media or verified equivalent. The coil behind gets foamed and rinsed only after pressure differential reads below 0.75 inches w.c.
- H2KM Hydroxyl Generator: UV-C lamp degradation masked by intact filament glow. The H2KM’s UV lamps still glow purple when the 254nm output has dropped below effective germicidal range. We meter actual UV output at the quartz sleeve surface. Below 40 microwatts per square centimeter, the lamp gets replaced regardless of visual condition. The surrounding reflector gets polished or swapped if oxidation has dulled the aluminum.
- PAS2400 Portable Air Scrubber: Condensate pan biofilm in high-humidity crawlspace installs. Fort Worth’s clay soils hold moisture, and PAS2400 units in pier-and-beam homes often sit in 70%+ relative humidity. The condensate pan develops a pink bacterial film that restricts drainage and back-feeds moisture to the blower section. We pull the pan, treat with EPA-registered sanitizer, and verify the drain line pitch with a level. No reassembly until the pan reads dry to touch.
- Abatement Technologies custom HEPA housings: Gasket compression set after Texas heat cycles. Rigid HEPA housings in attic installations see 140°F+ peak temperatures. The silicone gaskets take a compression set, and negative-pressure testing shows bypass leakage at the housing perimeter. We replace gaskets with Abatement Technologies-specified closed-cell silicone or document-equivalent, then run a DOP challenge test to verify 99.97% at 0.3 micron before sign-off.
Our Abatement Technologies HVAC Cleaning Process
- 1
System identification and written scope. We photograph the nameplate, confirm the model series, and check Abatement Technologies’s published service bulletin history for known issues on that unit. You get a written scope and price before we open the housing.
- 2
Negative-pressure containment setup. For units inside the conditioned envelope, we establish HEPA-filtered exhaust to protect your space. For attic or crawlspace installs, we seal the return path to prevent cross-contamination. Haven Standard Clause 1: Written Price Before Work Starts applies here.
- 3
Component-specific cleaning per manufacturer tolerances. Coils get foamed with pH-neutral cleaner, not caustic. Blower wheels get hand-cleaned or media-blasted depending on debris type. Heat exchangers get visual plus borescope inspection. We use Abatement Technologies-compatible tools or document the equivalent.
- 4
OEM versus quality aftermarket decision, documented. If a part needs replacement, we quote both options where available. Abatement Technologies OEM filters and lamps carry full warranty; selected aftermarket equivalents meet the same spec at lower cost, with the trade-off noted in writing.
- 5
Post-cleaning performance test and photo record. We measure static pressure, temperature split, and UV output where applicable. Every cleaned surface is photographed before reassembly. The photo record, test readings, and warranty terms are delivered as a single job file.
- 6
365-Day Done Right Promise activation. The written guarantee goes into effect at final signature. If airflow, noise, or temperature split drifts from our documented baseline within one year, we return and make it right.
BeforeAfterWhat Abatement Technologies HVAC Cleaning Costs in Fort Worth
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Evaporator coil cleaning (Abatement Technologies air handler) | $340 - $520 | Coil access (slab duct vs. attic), fin corrosion level, whether the drain pan needs removal |
| Blower motor and wheel cleaning | $280 - $440 | Bearing condition, wheel material (steel vs. composite), rebalancing needed |
| Condenser coil cleaning (outdoor unit) | $220 - $360 | Fins per inch density, hail damage, chemical restoration vs. standard foaming |
| Heat exchanger inspection and cleaning | $380 - $580 | Access panel configuration, borescope time, any crack protocol documentation |
| Full air handler service (coil, blower, housing, UV) | $680 - $940 | Unit size, filter bank count, UV lamp count, gasket condition |
| HEPA housing gasket replacement with DOP test | $420 - $640 | Housing size, gasket linear footage, access difficulty in attic or crawlspace |
These are whole-system prices, not per-vent or per-hour figures. The price we write is the price you pay. Bring a competitor’s written estimate and we’ll put our number beside it, no charge. Call (817) 520-8797 for a free estimate with no obligation to schedule.
Why Fort Worth Homeowners Call CleanRun Air Duct Cleaning Fort Worth for Abatement Technologies Work
We’ve been running jobs across Fort Worth since 2013, including plenty of work in the Near Southside where older homes hold decades of debris in ways newer builds don’t. Tomas Reyes, our owner, grew up in the Bronx and learned his first trade skills at Bronx Community College before spending years in the field learning exactly what accumulates inside residential and commercial duct systems when nobody’s paying attention. The camera doesn’t have a sales pitch. If the footage doesn’t show a problem, he’ll tell you that too.
Our technicians are background-checked, uniformed, and identified by name before arrival - Haven Standard Clause 3: Verified Crews. We also service Lennox, Trane, and Carrier equipment, so if your Abatement Technologies unit interfaces with another brand’s air handler or condenser, we don’t need a second contractor. Every job carries the 365-Day Done Right Promise in writing, and every customer receives the full photo record as a standard deliverable, not an upsell.
FAQs
No, if the work is performed to Abatement Technologies’s published maintenance specifications and documented with photos and test readings. We are an independent Abatement Technologies service provider, not an authorized dealer, and we follow manufacturer torque specs, cleaner pH limits, and filter media ratings precisely so your warranty stays intact. Call (817) 520-8797 if you need a copy of our warranty-safe protocol for your records.
We photograph every part label before installation and include it in your job file. If we propose a quality aftermarket equivalent instead, we document the spec comparison in writing and you approve before we proceed. Haven Standard Clause 1 requires this transparency.
Repair makes sense when the cleaning restores performance to within 10% of manufacturer specs and no structural component is compromised. We replace when the heat exchanger shows cracks, the coil has pinhole leaks at multiple fins, or repair costs exceed 60% of comparable replacement. Our written estimate shows both paths when the choice is close.
Most residential jobs finish in two to four hours. A full air handler service with HEPA housing gasket replacement in a tight Fort Worth attic may run five hours. We give you a time estimate in the same written scope that holds the price, so you can plan your day.
Every two to three years for standard residential use in Fort Worth. Homes with pets, recent renovation, or proximity to construction may need annual service. We don’t sell maintenance contracts; we photograph the current condition and let you decide based on what the camera shows.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning Fort Worth at CleanRun Air Duct Cleaning Fort Worth, serving Fort Worth and nearby areas.